Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

I have the B2410 with a John Deere 48 inch brush hog. The John Deere brush hog had different sets of lift holes for the 3 point lift allowing me to make the adjustment; however, I still can not lift it as high as I would like.

Kubota B2400 with 5 Bush Hog
Kubota Tractors
Replies 5 Post by Denny Townson

My neighbors B2410 has an intermitent problem where sometimes, it will not crank the engine. We have checked the safety switch for the clutch, and both PTOs. All three of these show continuity when checked with an ohm meter. Are there any other safety cutouts which would cause this problem. I can bypass all the switches and start it by running a jumper from the battery direct to the starter solenoid and that gets it going again. Next time he tries it may or may not start. Any ideas??

What cutout switch is keeping it from starting
Kubota Tractors
Replies 37 Post by Denny Townson

Thanks for all the replies. We are finally getting over it now to the point we can begin to laugh about it a little without being overwhelmed by the thought of what almost happened.

I think the suggestion to add weight to the back is correct. Why do you prefer the ballast box on a 3pt hitch to filling the tires?? I also think a tilt meter is a good idea. Can I find them on the web and what tilt angle is consider unsafe for the B2410?

Tractor Roll Over
Tractor Projects
Replies 27 Post by Denny Townson

I have a B2410 and would like to purchase the Kubota front mounted snowblower. My question is this: Does the snowblower mounting brackets require that I remove the FEL mounting hardware or can I just remove the FEL and leave the mounting brackets for it in place. If so, then I would be able to switch between the FEL and the snowblower. I know some of you will suggest that I purchase a rear mount snowblower. I could do that but my driveway is over 1500' and I am not sure I want to be backing up that distance all the time. <br>

Front mount snowblower vs Front End Loader Mounting bracket
Snowblowers / Snow Plows
Replies 3 Post by Denny Townson

I recently purchased the Kubota B 2410 with the Landpride 60" rear discharge mower model FDR1560. It has the pneumatic air filled rubber tires, 18,264 fpm blade tip speed weight is 492 #, deck is 10 gauge steel. It does a nice job and I am completely satisfied with it. As a package deal with tractor and other implements, the dealer charged me $1400.

3ph finish mower what brand type
Mowers Field and Finish
Replies 13 Post by Denny Townson

I am getting a new Kubota 2410 this week with FEL and rear finish mower. Later this fall, I plan to buy the front mounted snowblower. How difficult is it to change from the FEL to the snowblower? Is this a once a season task or can I change back and forth easily during the winter?

How hard is it to change from FEL to Snowblower
Tractor Projects
Replies 1 Post by Denny Townson

I read the earlier post for the 35w and 50w bulbs for the B series Kubota. Which have you used and which seems to be the best answer?

50w or the 35w High Intensity Bulbs for the 2410 Kubota
Kubota Tractors
Replies 3 Post by Denny Townson

I am purchasing a 2410 with FEL and rear finishing mower. Should be delivered this coming week. Later this fall I plan to purchase the front mounted snowblower. My driveway is 1500' and this past winter we had so much snow the snow plow could not get down it at all. It was too high on the sides so I cranked up my walk behind snowblower (28" cut) and cleared it out so it was passable. My dealer has not said how difficult it is to change between FEL and snowblower but I will ask him this week. BTW, I do not plan to change during the winter. My neighbor also has a 2410 and we have agreed that he can use my tractor with the snowblower and I can use his with the FEL. That will keep me from having to change it back and forth on my tractor.

BX2200 snowblower vs fel
Kubota Tractors
Replies 5 Post by Denny Townson

Here is what I have gathered so far.
Landpride RCR1548-1231: Deck is 12 guage, Gearbox is rated at 30hp and 45
in cut. Cost is $995

Bush Hog SQ480: Deck is 11 guage, Gearbox is rated at 45hp and 48 in cut.
Cost is $974

Howse 400: Deck is 12 Guage Reinforced, Gearbox is 45hp and 48 in cut.
Cost is $570 but can not find a dealer in my area so freight will add to
that cost.

Looks like the Howse may be the best buy but may not be able to find it
locally

bush hog brush hog rotary mower
Mowers Field and Finish
Replies 12 Post by Denny Townson